How To Splice Cat 5 Cable
If you’re like most people, you probably use a lot of CAT5 cable when networking your home or office. But if you’ve ever tried to splice a CAT5 cable, you know it can be a pain. In this article, we’ll show you how to easily splice a CAT5 cable using a simple DIY technique.
How to make CAT-5 Cable / Network Wire – Tutorial Guide
[ytvideo]
How to Splice Cat Cable
If you’re like most people, you probably splice your cat5 cable when a wire goes bad or when you want to extend your cable. But what’s the best way to do it?
The best way to splice cat5 cable is with a connector. There are a number of different types of connectors out there, but the most common one is the RJ-45 connector.
To splice a cable, start by marking the end of the cable you want to splice with a light pencil or a piece of tape. Then, connect the marked end of the cable to the connector on the end of the cable you want to splice.
Next, pull the marked end of the cable away from the connector. Hold the connector and the marked end of the cable in opposite hands, and push the connector onto the marked end of the cable until it’s fully seated. Then, hold the cable in one hand and twist the connector counterclockwise to tighten the connection.
That’s it! Now you have a fully spliced cable.
What You’ll Need
-A cable splicer
-A cat 5 cable
-A RJ45 connector
-A screwdriver
-A wire stripper
-An RJ45 connector
-A cat 5 cable
-A RJ45 connector
-A screwdriver
-A wire stripper
- First, take the RJ45 connector and strip the wires going into it. You will need to strip about an inch of each wire.
- Next, take the screwdriver and unscrew the RJ45 connector from the cable. You will need to remove the four screws that hold it in place.
- Once the RJ45 connector is free, insert the stripped wires into the connector and screw it back in place.
- Now, take the cat 5 cable and insert the RJ45 connector into one end. Strip the wires going into the connector as you did with the RJ45 connector in step
- 5. Next, strip about an inch of the wire going into the cable and insert it into the RJ45 connector on the other end of the cat 5 cable. Screw the connector back in place.
- Finally, strip the excess wire off the ends of the cables. Now you are ready to splice the cables together.
Splicing cat 5 cables is a relatively simple process that can be done with just a few basic tools. First, you will need a cable splicer. This device can take two cables and join them together so that
Measuring and Cutting the Cable
First, measure the distance between the two devices you want to connect and make a rough sketch of the cable you want to make.
Next, cut the cable to the correct length. The distance between devices should be about the same length as the cable you’ve drawn on paper.
Finally, splice the cable in the correct places. There are a few different ways to do this, but the most common is called “sticking”. This means pulling one end of the cable tight, then looping it over and under the other end, then pulling the ends tight again.
Stripping the Wire
When you are stripping the wire on a Cat5 cable, the red and green wires go on the left side, and the black and white wires go on the right side. The black wire is the “hot” wire, and the white wire is the “neutral” wire. The red wire is the “positive” wire, and the green wire is the “negative” wire.
To splice a Cat5 cable, you first have to identify the positions of the wires. The black wire goes in the first “hole” on the connector, the red wire goes in the second “hole”, and the white wire goes in the third “hole”. The “holes” are usually numbered 1, 2, and 3, but they may also have different names, like “jumper,” “pin,” or “female.”
Next, you have to determine the length of the cable you need. The black wire should be about 2 inches (5 cm) shorter than the red wire, and the white wire should be about 2 inches (5 cm) shorter than the green wire.
The easiest way to do this is to cut the cable in half. Then, you can measure the length of the black wire, and add 2 inches (5 cm) to that measurement. You can then measure the length of the red wire, and add 2 inches (5 cm) to that measurement. You can then measure the length of the white wire, and subtract
Splicing the Cable
Splicing the cable is a task that can be easily done by almost anyone with a little bit of know-how. It is important to remember that no matter how carefully you do the splicing, there is a chance that some of the cable’s insulation may be damaged. If this happens, the new cable will not work and you will have to replace it.
The most important thing to remember when splicing the cable is to use a good quality cable and make sure the splice is well made. You also want to make sure that the cable is properly heat-shrunk. Finally, do not use too much force when making the splice.
Finishing Up
Assuming you are using a proper tool like a wire stripper, the process is simple.
- Strip 3/8″ of insulation off both ends of the cable.
- Connect one wire to each end of the cable.
- Twist the wires around each other a few times to form a loop.
- Crimp the ends of the loop together.
- Strip the remaining insulation from the cable.
Tips and Tricks
Splicing Cat 5 Cable:
In order to splice Cat 5 Cable, you will need:
-An RJ45 connector
-A pair of wire strippers
-A RJ45 crimp tool
-A piece of stranded wire
-A connector
-A Cat 5 cable
-A RJ45 connector strip
-A piece of double-sided tape
- Strip the ends of the cable of any insulation. This can be done with a pair of wire strippers or a RJ45 crimp tool. Be sure to leave a short enough tail on the cable to easily connect it to the connector.
- Connect the connector to one end of the stranded wire. Make sure the wire is long enough so that it extends beyond both ends of the connector.
- Strip the insulation from the other end of the stranded wire.
- Strip the insulation from the end of the cable that you connected to the connector in Step
- Make a loop in the cable, placing the stripped end of the cable inside the loop.
- Push the other end of the cable through the connector, stretching it so that it covers the entire loop.
- Crimp the cable connector onto the stripped end of the cable.
- Repeat Steps 2-7 for the other end of the cable.
Conclusion
In order to splice cat 5 cable, it is important to follow the correct steps. First, cut the cable to the correct length. Second, strip the wires. Third, make a makeshift connector. Fourth, attach the wires to the connector. Fifth, splice the wires together. Finally, attach the connector to the cable.